Black Seal TC Practice Exam

These questions are part of the practice quiz. Start practicing

• At 100 psi, what is the dry saturated steam temperature?
• What type of test should be conducted on a boiler after it has undergone maintenance or repair?
• What type of cycle is typically used in steam turbines?
• Before starting a hot water heating plant, what is the minimum water level expected in an expansion tank?
• How many BTUs can the burning of one gallon of #6 oil produce?
• What type of steam is produced at a pressure of 100 psi?
• What is the minimum size of a manhole found on a boiler?
• Why are baffles used in the steam drums of water tube boilers?
• Which formula would you use to calculate the Btu/lb. heat content of fuel oil?
• If your license expired and you pay a penalty, how long can it be expired before you need to re-apply and retake the exam?
• Which valve must be present between the safety valve and the boiler?
• What does 2545 Btu hours represent?
• Which of the following best describes a boiler's function in an industrial setting?
• On a turbine driven feedwater pump, which piping is typically larger?
• What should the range of the pressure gauge be in relation to the MAWP of the boiler?
• During combustion in a boiler, which gas is produced as a by-product?
• What is the minimum thickness allowed for an atmospheric type blowdown tank?
• Before the burner ignites, what is the minimum number of furnace volume air changes required by the purge cycle?
• Which factor is crucial for achieving optimal combustion conditions?
• Why is it essential that there be no valve between the safety valve and the boiler?
• What type of boiler system operates under positive pressure during various load conditions?
• Which valve offers the least amount of restriction?
• How are tube sheets supported in a fire tube boiler?
• In fire tube boilers, what is the main function of the shell structure?
• A three-element feedwater regulator is controlled by which of the following?
• What device is used on a deaerator to prevent water from backing up into the steam line?
• What should be done to replace a lost nameplate on a boiler?
• What are the consequences for an applicant caught copying exam questions at an exam site?
• What is a potential result of water hammer in a steam plant?
• What could be an effect of not conducting regular maintenance on boiler tubes?
• When is a mercury-tube pressure control most accurate?
• What is the main function of a safety valve on a boiler?
• What is an adverse effect of not maintaining the correct temperature for stored #6 oil?
• What is the heating surface area of a water tube with a diameter of 3 ½" and a length of 20 ft?
• How much work does one mechanical horsepower equal in terms of foot-pounds per minute?
• What is an important safety measure for high pressure boilers?
• For maximum efficiency, where should sodium sulfite be added in a boiler system?
• What would the specific volume of water be at 60°F?
• What is the definition of sensible heat?
• What is the primary objective of managing combustion air temperature in a boiler?
• Which valve is considered the most important on a boiler?
• Boiler tubes are measured by what dimension?
• Who is authorized to readjust the setting of a safety valve on a pressure vessel?
• What is a primary purpose of a vent condenser on a deaerating feedwater heater?
• Which component of a safety valve ensures it seats properly?
• In what unit are vaporstat type pressure switches calibrated?
• What is defined as the evaporation of 34.5 pounds of water?
• What can be expected if flue gas temperatures are too low in a fire tube boiler?
• What is the overspeed trip setting on a turbine with a normal operating speed of 1770 rpm?
• What is a common method to increase boiler efficiency?
• What kind of fuel conversion is necessary for a combustion process in a boiler?
• What is the horsepower of a boiler with a capacity of 35,500 lbs steam/hour and an evaporation rate of 10 psi?
• In a steam pressure gauge, which part straightens from steam pressure to indicate a reading?
• What is one standard atmosphere at 14.7 lbs per square inch equivalent to in feet of water?
• Which component is used to measure steam pressure?
• What is crucial for maintaining the efficiency of a pressure fired boiler?
• What is the minimum age requirement to obtain a black seal fireman's license?
• What condition occurs when a baffle breaks in a fire tube boiler?
• What would likely be a sign of insufficient blowdown?
• What issue does calcium and magnesium cause in a boiler?
• What is the purpose of a safety valve on a boiler?
• In which situation is a licensed fireman not needed in a boiler room?
• What would likely happen if the entire system is not properly deaerated?
• What amount of Btu is required to raise the temperature of 1 pound of water from 32F to 212F?
• In a water tube boiler, where do the gases of combustion pass?
• What is one main purpose of using baffles in steam drums?
• What device is used to measure draft in a boiler?
• Where is the registration number found on a boiler registration certificate?
• How do Mechanical Inspection Bureau rules classify steam boilers?
• Where should the boiler bottom blowdown line discharge to?
• Which condition requires the use of demineralized water in high pressure boilers?
• How often should boilers in New Jersey be inspected internally and externally?
• Which device would typically be found on the inlet line of a steam turbine condenser?
• In a water tube boiler, what is the function of downcomer tubes?
• What type of engineer is required for high pressure plants rated over 500 to 1,000hp?
• What water temperature qualifies as a high pressure hot water system in a hot water heating boiler?
• What is a common cause for a dirty fuel oil strainer?
• At what steam pressure does a feedwater heater typically operate?
• How many foot-pounds per minute is 1 mechanical horsepower equal to?
• Saturated steam is defined as?
• How do you test the operation of the fire-eye on a gas-fired boiler?
• In a fire tube boiler, what is a potential consequence of improperly rolled tubes?
• Where is caustic embrittlement typically found in a boiler?
• Shrouds are found on which piece of auxiliary equipment?
• What type of draft system is used to overcome resistance on boilers equipped with an economizer?
• How is steam prevented from entering the Bourdon tube of the pressure gauge?
• What could indicate a malfunctioning safety valve?
• What is a likely cause for a gradual increase in stack temperature?
• What system is employed to ensure safe operation of a steam boiler during firing?
• What are the three types of draft commonly used in power plants?
• What is the purpose of boiler blowdown?
• Baffles direct combustion gases to come in close contact with what?
• If steam is reduced by a pressure reducing valve (PRV) from 500 psi to 125 psi, what can be said about the steam at 125 psi?
• Which statement best describes the operation of a closed feedwater heater?
• How many feet of water does one standard atmosphere equal?
• What does a thermal expansion feedwater regulator rely on to operate?
• What type of valve should be positioned closest to the boiler on a feedwater line?
• If the air temperature entering a heater is too low, what is a common result?
• Which two elements are primarily responsible for the heat generation in fuel oil?
• What state is steam at 100 psi and 400F?
• What is the proper oil storage temperature for #6 oil?
• Which safety device is critical for preventing boiler over-pressurization?
• During safety valve testing, what percentage of popping pressure must be achieved?
• When adjusting the firing rate of a boiler, why should air be increased to the burner before fuel?
• Which of the following is a function of a stop valve in a boiler system?
• What essential factors contribute to complete combustion in a boiler?
• Which statement is true regarding flue gas flow in a fire tube boiler?
• Who is responsible for determining how long a boiler operator can be away from their boiler in New Jersey?
• What formula is used to calculate the Btu/lb heat content of fuel oil?
• Shrouds are typically associated with which type of auxiliary equipment?
• What safety measure should be taken for a boiler's safety valve?
• What is the minimum age requirement to obtain a black seal fireman’s license?
• What is a primary function of a deaerator in a boiler system?
• What produces mechanical draft in a boiler system?
• What is a common indication of insufficient secondary air during combustion?
• Why are economizers used on boilers?
• How many Btu's is one boiler horsepower equivalent to?
• What condition may lead to a decrease in boiler efficiency?
• Which valve must be present between the safety valve and the boiler?
• The conversion of 2,545 Btu's equals how many horsepower hours?
• What will cause pitting of boiler metal?
• What is a common cause of a feedwater pump becoming vapor bound?
• What device removes moisture from steam before it enters the header?
• A high pressure differential across a fuel oil strainer indicates what condition?
• What might be an indicator of a high-pressure hot water system?
• What is the term for the heat absorbed by boiler water when changing from liquid to steam?
• Which of these is a key factor in determining the efficiency of a boiler?
• Which type of thermometer is commonly used in steam boiler systems?
• What should be checked regularly to ensure proper boiler operation?
• Why is maintaining the boiler water temperature at 70F prior to a hydrostatic test important?
• What is the purpose of the economizer in a boiler system?
• What is the absolute pressure of a boiler operating at 160 psig?
• What is the primary function of a safety valve in a boiler?
• Which condition indicates a balanced draft system in a boiler?
• What is the role of the blowdown tank?
• What occurs when two similar centrifugal pumps are connected in parallel?
• What is total force in relation to pressure and area?
• Where would you find a cyclone separator?
• What is the primary role of an expansion tank in a hot water heating system?
• How many Btu's are necessary to change 1 pound of water at 212F into 1 pound of steam at 0 psig?
• A two-element feedwater regulator is primarily controlled by which factors?
• What is the heating surface of a water tube with a diameter of 3 ½ inches and 20 feet long?
• What ASME code denotes a high-pressure power boiler?
• Which best describes balanced draft?
• What is the name of the simple power plant cycle used in many thermal power systems?
• What is the purpose of a dry pipe system?
• How are tubes attached to the tube sheet in a fire tube boiler?
• Where is a cyclone separator typically found in a boiler system?
• Why are boiler manways and handholes oval?
• How many BTUs are in 5 therms of gas?
• Which component is primarily responsible for converting water to steam in a boiler?
• What should be checked before operating a boiler system?
• What is the typical function of a stack in a boiler system?
• In what units are pressure gauges typically calibrated?
• Which component is vital for ensuring safety in boiler operation?
• Why are economizers used on boilers?
• What type of steam is produced when steam is at 100 psi and 400 degrees F?
• Why are boiler manways and handholes designed to be oval?
• In what type of boilers can downcomer tubes be found?
• Which type of boilers require demineralized water?
• How much steam does one boiler horsepower equal at 212F according to the NJ Mechanical Inspection Bureau?
• What method can prevent a furnace explosion?
• What is an essential characteristic of good boiler water quality?
• Which chemical is used to control alkalinity in boiler feedwater?
• How much does one pound of water expand when it turns into steam at standard temperature and pressure?
• Which stack gas reading would show good combustion?
• What is the effect of low combustion temperatures when burning #6 oil with high sulfur content?
• A boiler with a capacity of 5,021,250 Btu's is equivalent to how many horsepower?
• The total force on a safety valve with a 2 ½ inch diameter at 15 psi is what?
• What is one effect of negative caustic embrittlement in a boiler?
• When should the air vent or cock be closed during operation?
• What does the boiler certificate indicate?
• Which of the following accurately describes a forced draft fan?
• Which ASME code covers power boilers?
• What is typically a consequence of having too high a water level in a boiler?
• What is required between the steam outlets of two connected boilers?
• With a high-pressure license, what is the maximum plant size a person can oversee as chief engineer?
• What is the main function of a stay bolt in a boiler?
• One mechanical horsepower is equal to?
• What should be done with the safety valves during a hydrostatic test?
• What is the purpose of a pressure reducing valve in a steam system?
• If a person's license expires and they pay a penalty, how long can it be expired before they must re-apply and retake the exam?
• What is the purpose of a by-pass damper on boilers equipped with an air pre-heater?
• When a boiler is in a priming condition, what is occurring?
• What is the horsepower of a boiler that has an evaporation rate of 10 lb/ft² of heating surface per hour and can produce 35,500 #/hr?
• How often should you blowdown a boiler with no chemical water analysis?
• What happens if the pressure gauge range is less than the MAWP of the boiler?
• What is the purpose of small holes drilled in the ends of stay bolts?
• How many days before expiration can you renew your license?
• A stack temperature of 250°F above steam temperature indicates what?
• What temperature is best for boiler water when preparing for a hydrostatic test?
• What two ingredients are commonly used as oxygen scavengers?
• What is considered atmospheric pressure?
• Which type of steam trap has no moving parts?
• What is often the result of too high a stack temperature?
• What is the total force acting on a safety valve of a 325 psi boiler with a 2 ½' diameter safety valve?
• How does excessive air affect combustion efficiency in a boiler?
• What is the sequence for opening and closing a quick-opening valve when blowing down a boiler?
• Which type of heater is commonly used to ensure the quality of feedwater in steam boilers?
• What type of draft system utilizes atmospheric conditions for air induction?
• What unit of measurement are manometers calibrated in?
• In the State of NJ, how often should safety valves on high-pressure boilers be tested by hand?
• Where is caustic embrittlement most frequently observed in boiler systems?
• What can happen if moisture is allowed to enter the steam lines?